| Results 1 - 8 of 9 |
Page 1 of 2 |
|
|
|
pannier racks
|
Tuesday, 13 May 2008 |
|
|
|
stock Bmw pannier racks off 1992 GSPD just powder coated new condition 100.00 firm |
|
|
|
Phone: 1250-753-2653 or 1250-802-7009 |
|
|
|
|
R75/7 1977
|
Monday, 12 May 2008 |
|
|
|
R75/7, nice overall condition, 97500 miles, looks great next to other bikes from the same year. Some scratches on the tank from the seat pan, but no dents. Recently replaced push rod seals and main bevel drive seal, brake pads. The bike comes with BMW hard bags, no dents, all locks working and a Luftmeister fairing with all it's docking and harness in tact, not on the bike. I have some other bits and pieces I will give away as part of the sale. I have had this bike about 7 years and it's been a great experience, sorry to have to let it go. $2200. |
 |
|
|
|
Phone: 6268405275 |
|
|
|
|
1984 R100RT "FINAL EDITION"
|
Monday, 12 May 2008 |
|
|
FOR SALE: 1984 BMW R100RT ‘FINAL EDITION’ Asking $5000.00 – MUST SELL ...........
A great ride for the serious “AIRHEAD” aficionado. Purchased with 30,000 miles on the odometer. Ridden a bit more than 1000 miles since restoration. The bike did not show any signs of abuse at purchase, only neglect...........
Purchased June 2007 for $3000.00. More than $2000.00 invested in parts and subcontracted services............ Approximately 600 hours of research/study and wrench twisting to restore the bike to its current condition. Most of the paint is original...........
A retired toolmaker/machine builder did the restoration process............
A list of the parts and services (with pricing) used in the restoration is shown below. Suppliers are listed in hidden columns.
Mileage Work Performed Cost
30000 Glass bead wheels $50.00
30000 Clear Powder Coat Wheels $200.00
30000 Remove Tires & Bearings $47.00
30000 Metzler Lasertech Tires $253.72
30000 (2) Tubes & (2) Spares $38.18
30000 Mount and Balance Wheels $40.50
30000 Front Wheel Bearings $39.66
30000 Stainless steel header pipes and crossover tubes $265.00
30000 Rear Wheel Bearings $39.66
30000 Valve Cover Gaskets $21.95
30000 Diode Board Kit $96.65
30000 Dust Cover $31.00
30000 Classic Boxer Charging Manual $26.50
30000 Wheel Bearing Seals $26.95
30000 Fairing Gasket Set $57.85
30000 Locktite Prism Glue for Fairing Gaskets $18.32
30000 Accessory Power Socket, Oil Filter Kit, Air Filter, Fuel Filters (2), Halogen Bulb $112.73
30000 Voltage Regulator, Diode Board Solid Mount Kit, $58.65
30000 Carb Cleaner $6.39
30000 Spark Plugs, Fork Oil, Gear Oil (2), Brake Fluid, Castrol 20W50, Electro -Seal Sealent $89.65
30000 Misc. Seals $20.95
30000 White Lithium Grease, Molycoat Cartridge, Grease Gun, Antiseize Compound, Hose Clamps for Fuel Lines, Fuel Line, Hose Clamps for Exhaust $98.89
30000 Wheel Bearing Greaser $24.00
30000 Oil Pressure Switch $21.98
30000 Kano Kroil Penetrating Oill $21.92
30000 Airhead Exhaust Nut Wrench $36.46
30000 Wheel Spacers and Misc. Gaskets $51.55
30000 Brake Light, Clutch Cable, Collar, Boot, Grommet $57.85
30000 Odyssey Dry Cell Battery $120.00
30000 Misc. Paint, Lubricants, Fluids, Cleaners $100.00
TOTAL COST $2,073.96...........
Plus I probably missed a few hundred dollars in misc. parts and service..........
In addition to parts and subcontracted services, the following work has been done during the restoration process:
• Wheels removed, glass beaded & clear powder coated
• Bike was stripped down to the frame, most of which was repainted
• Installed and balanced new Metzler Lasertech tires.
• Installed and adjusted preload on front and rear wheel bearings
• All component parts were cleaned, repainted and waxed during reassembly
• Charging system rebuilt/rewired – Omega diode board with solid mounts
• New heavy duty voltage regulator installed
• Accessory 12V socket installed
• New Oddyssey Extreme dry cell battery installed. Can be stored for two years on a full charge without failing.
• Valves adjusted and new valve cover gaskets installed
• Carburetors cleaned and adjusted
• New spark plugs installed
• Complete tune up sequence performed from plug installation to carburetor balancing
• Replaced fuel lines and added aftermarket filters
• Gas tank epoxy coated inside – tank was flushed, cleaned and new internal filters installed
• Transmission and clutch splines cleaned and lubricated
• Brake lines drained, flushed and refilled with new fluid – brake pads are 80%
• Oil and filter changed
• Transmission, driveshaft & final drive fluids replaced
• Swing arm bearings removed, cleaned, greased, replaced and adjusted
• Clutch adjusted...........
Following is a list of special tools (purchased and custom built) and documentation that go with the bike:
• Custom made spacers (2) for setting the preload on front and rear wheel bearings
• Finned exhaust nut wrench
• Classic Boxer Charging Manual by Rick Jones
• Home built manometer for balancing carbs
• Manuals and custom instruction folder for mechanical troubleshooting/repair/adjustment of major components. Explosion drawings, torque chart and part lists included (with dirty finger prints)
• Maintenance schedule
• 2008 BMW owners Anonymous Book..........
Following is a list of spare parts and materials that go with the bike:
• Spare halogen headlight bulb
• Wheel preload shims
• Wheel bearing lubrication tool
• Spring balance for adjusting wheel bearing preload
• Misc. bulbs
• Cotton dust cover
• Replacement clutch cable
• Fork oil
• Cleaners, wax. Lubricants and Misc............
Following is a list of items that need done to make the bike 100% mechanically & electrically complete (I ran out of time):
• Oil change (last changed fall of 2007 prior to winter storage)
• Loosen all fairing screws, realign components and retighten – it’s tweaked out of square a bit.
• Front turn signals do not work – repair
• Horns do not work – repair
• Replace front fork oil – in stock
• Redo tune up to improve engine response
Exceptions:
• Minor damage to fairing and left side mirror
• Mismatched paint color on one new battery cover
One change that I had planned was to remove the tires/tubes and spotface the inside of the rim at the valve hole. Replace the tires without tubes to make roadside repairs possible. I researched this thoroughly and it can be done safely with the BMW snowflake wheels.
|
 |
|
|
|
Phone: 651.592.1521 |
|
|
|
|
2006 v-strom 1000 for sale
|
Sunday, 11 May 2008 |
|
|
|
I have a very clean low mileage Suzuki Strom for sale,1100.00 in extras and am asking 6200.00 for the bike. Im building up a R75/6 so wont be needing the strom. #530-893-8029 in Chico. Brad. |
 |
|
|
|
Phone: 530-893-8029 |
|
|
|
|
Greta must go
|
Saturday, 10 May 2008 |
|
|
|
My wifes 73 SWB R75/5 Toaster needs to find a new home. 41k miles, wixom bags/trunk, newer mufflers, tires, new dealer refurbished motometer. She has been in the family for over 20 years. If you're secure with your masculinity you can ride a girly colored bike, ( or repaint it)$4000.00 or reasonable offer. |
 |
|
|
|
Phone: 406-671-0452 |
|
|
|
|
R100RT - 1982
|
Wednesday, 07 May 2008 |
|
|
121k - $3.5k - brand new clutch, rebuilt gearbox, new input shaft. Top end, diode board at 110k. Smoke red. Side cases, original owners manual and pump (but not the tool kit). The paint is not at all pristine, but she is mechanically sound and a very strong runner. Purrs like a kitten. Includes the rare euro running lights in fairing and headlight switch. Corbin seat, Koni rear shocks. Metzlers have less than 500 miles on them. The bike spent most of its life belonging to the father of a BMW mechanic who kept it in perfect mechanical shape. Fairing lowers and Parabellum windscreen currently removed but included (of course). Next thing to fix is a slightly notchy steering head. I'm selling it because I got a (nearly) naked bike and I realized that I'm just not a fairing kind of rider.
The bike is in Chicago. |
 |
|
|
|
|
|
|
|
misc parts
|
Tuesday, 06 May 2008 |
|
|
|
Raask rearsets off of a 1978 R100/7 $250.00, Delorto carbs $350.00, set of wire spoke wheels $300.00, after market seat $ 250.00 all items plus shipping and are best offer. |
|
|
|
Phone: 308-631-2162 |
|
|
|
|
2004 Honda Intercepter SOLD*SOLD
|
Saturday, 26 April 2008 |
|
|
2004 Honda Interceptor (3, 684 Miles) $6,700 OBO
Recently married, baby just arrived so I need to sell this un-dropped, non-trashed beautiful example of Honda's best work for the 2004 Honda 800cc, five valve Interceptor Matte Black. It comes completely stock, with a new rear tire with 2 miles on it. Will be willing to transport, let's discuss.
This vehicle is sold as is for $6,700 and does not include a warranty; I accept cashier's checks, cash, wire transfer. The vehicle title is clear and in my possession, so we can close the transaction as soon as the funds are transferred. Please call (802) 849-6941 evenings or e-mail at vtairhead[<@>]verizon.net |
|
|
|
|
|
|
<< Start < Prev 1 2 Next > End >> |
)
)
)
)
)
