Please note that orders will not be shipped from 09/20/25 until 10/15/25. Dismiss

FORUM

David Elkow
David Elkow
@4949
Reputable Member
Joined: 08/24/2020 18:19
Last seen: 09/15/2025 05:08
Topics: 13 / Replies: 345
Reply
RE: 1975 R90/6: Occasional miss, high speed cut out

Probably not the issue, but Jeff C. reminded me of another occasion I had when my ‘78 had points. Can’t recall where I purchased the problematic point...

1 year ago
Forum
Reply
RE: Low speed vibration R80RT

Hello Peter. I have been curious about your issue. Any determination? (Also feeling your frustration.)

1 year ago
Forum
Reply
RE: "Stickies" or a "Must Read / Top 10 Issues" Sub-forum

The ADVrider forum … I recently was stuck with a very leaky oil pressure switch on my /7. Could not get a replacement where I was. I was “googling” in...

1 year ago
Reply
RE: Activity in Texas??

I live down in the RGV, in Mission. Agreed, there doesn’t seem to be any ABC activity in Texas. I think there might be a tech day once a year in the D...

1 year ago
Reply
RE: Occasional mis, high speed cut out

No personal experience, but I’ve heard of iffy kill switches causing faults. They interrupt the 12v circuit to the coils - so kill the ignition. Th...

1 year ago
Forum
Reply
RE: Occasional mis, high speed cut out

You may need to catch us up a bit. Did this occur prior to installing the new ignition, or since? I’m no expert, but in my simple thinking a mis-fire...

1 year ago
Forum
Reply
RE: Low speed vibration R80RT

Oops - just occurred to me, your forks are newer / different than mine. So, not sure how your sliders drop off.

1 year ago
Forum
Reply
RE: Low speed vibration R80RT

Reading your initial post, I see that you replaced the steering bearings. I just did mine, as well. Boy, they were shot. Anyway, so you had the fork t...

1 year ago
Forum
Reply
RE: Low speed vibration R80RT

I’m feeling your frustration. Hope you get an answer from the wheel place. Reading your plight jogged my memory. Nearly an eternity ago, I had a si...

1 year ago
Forum
Reply
RE: Low speed vibration R80RT

Any progress on this issue? I’ve been reading with curiosity… what could it be?

1 year ago
Forum
Reply
RE: Exhaust Muffler/Silencer Replacement Advice

(Worthless, irrelevant comment). Sometimes it just strikes me as funny. Us guys with these old bikes. When we put things together, we either use “Anti...

1 year ago
Forum
Reply
RE: '75 R90/6, Bing Carbs, inconsistent spark plug appearance

I’m presuming since you verified that the needles were in the correct position, that it was also verified that both needle jets are 2.68’s. Also impor...

1 year ago
Forum
Reply
RE: '75 R90/6, Bing Carbs, inconsistent spark plug appearance

I agree, the slide needles and needle jets should last many miles, and it is unlikely that one side would wear differently. Myself, if it were a “new ...

1 year ago
Forum
Reply
RE: '75 R90/6, Bing Carbs, inconsistent spark plug appearance

Hello Scott, if you get back into your carbs, and you didn’t last time, I would replace the slide needles and needle jets. It looks like (on that Bing...

1 year ago
Forum
Reply
RE: '75 R90/6, Bing Carbs, inconsistent spark plug appearance

PS: The needle notch on the Bing chart is called “clip position”. 1 is most lean, 4 most rich.

1 year ago
Forum
Page 5 / 24

Advertisement

Scroll to top