FORUM

Notifications
Clear all

Head stud pulling loose

3 Posts
3 Users
0 Reactions
12 Views
Charles parkel
(@charles-parkel)
Posts: 1
New Member Customer Registered
Topic starter
 
[#3359]

Greetings airhead community!

while attempting to adjust the valves on my 1987 R80, the adjustment nut was very tight. I was attempting to loosen the nut when i noticed it was free spinning. I purchased the 4 pack of EME EnDuraLast valve adjustment screw, and while removing the rocker arm I noticed the top nut was completely lose. I then attempted tightening it the rocker arm head nut and my heart sank when it felt spongy.

I immediately stoped my wrenching and looked up the condition online. Through my research I discovered I need a Northwoods Airheads jig to properly re drill the engine, as well as of course the exhaust bolt wrench I was planning on picking up from EME.

 

i can’t find the jig!! My fingers are crossed this community can help me find / rent / borrow the jig needed to get this bike back on the road.

 

many thanks,

 

Chaz


 
Posted : 11/19/2026 15:58
James Strickland
(@8053)
Posts: 466
Honorable Member
 

If you live in Wisconsin, your Airmarshal, Randy Boris, has a drill and tap guide.


former Airmarshal, IL.

 
Posted : 11/20/2026 05:49
Richard W
(@wobbly)
Posts: 2814
Member
 

Although the jig might be helpful, its use may not be "mandatory". 

The object of your effort is to remove the head, cylinder and piston off the engine so that you can re-tap the stud hole and add a HeliCoil to the stripped stud hole. Correct HeliCoil taps come with a lead-in section of thread that matches the original thread. Yes, you have a pulled out thread, but there is usually enough remaining thread/hole to guide the HeliCoil tap correctly.... especially if you go VERY slow and don't try to rush things. 

I've installed dozens of HeliCoils during my career and have learned lots of tricks. Here are some to help you...

1. You'll need generous lubrication. In this case some common "chassis lube". a) Lubrication to not only reduce your effort, but more importantly catch and retain all the aluminum chips in the tap so that they don't get loose inside the engine. Every 1/2 turn or so you'll need to remove the tap, wipe it clean, and apply new grease. b) Lubrication will also result in the best possible finish on your newly tapped hole. 

2. This is EXTREMELY important. You must turn the tap with a T-handle so that pressure is applied equally to both sides. If you use something like a common (one-handled) socket ratchet, then the torque will be one-sided and the hole will go WAY off course. This job is further complicated by the remaining 3 studs. You must either remove those studs or construct a rigid T-handle tap tool holder with an extension longer than the 3 remaining studs.

Additionally if one stud hole is buggered, then you might consider that all 4 studs got the exact same assembly treatment, and HeliCoils may be required on all 4 stud holes. That depends on what other evidence of mistreatment you find while you do the work.

3. You must get yourself a torque wrench to prevent further damage. You might even want to back-off the published head bolt torque. If that published number is (say for instance) 55 ft-lbs, then consider that 50 might do just as well. All 4 studs need to be equally torqued for the best outcome and the only way to get that is with a good torque wrench.

Hope this helps.


This post was modified 10 minutes ago by Richard W

Owning an old Airhead is easy.
Keeping an old Airhead running great is the true test.

 
Posted : 11/20/2026 05:55

Advertisement

Scroll to top